Afrikaans
Akan
Albanian
Amharic
Arabic
Armenian
Azerbaijani
Basque
Belarusian
Bemba
Bengali
Bihari
Bosnian
Breton
Bulgarian
Cambodian
Catalan
Cebuano
Cherokee
Chichewa
Chinese (Simplified)
Chinese (Traditional)
Corsican
Croatian
Danish
Dutch
English
Esperanto
Estonian
Ewe
Faroese
Filipino
Finnish
French
Frisian
Ga
Galician
Georgian
German
Greek
Guarani
Gujarati
Haitian Creole
Hausa
Hawaiian
Hebrew
Hindi
Hmong
Hungarian
Icelandic
Igbo
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kazakh
Kinyarwanda
Kirundi
Kongo
Korean
Krio (Sierra Leone)
Kurdish
Kurdish (Soranรฎ)
Kyrgyz
Laothian
Latin
Latvian
Lingala
Lithuanian
Lozi
Luganda
Luo
Luxembourgish
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Mauritian Creole
Moldavian
Mongolian
Myanmar (Burmese)
Montenegrin
Nepali
Nigerian Pidgin
Northern Sotho
Norwegian
Norwegian (Nynorsk)
Occitan
Oriya
Oromo
Pashto
Persian
Polish
Portuguese (Brazil)
Portuguese (Portugal)
Punjabi
Quechua
Romanian
Romansh
Runyakitara
Russian
Samoan
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Seychellois Creole
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
Spanish
Spanish (Latin American)
Sundanese
Swahili
Swedish
Tajik
Tamil
Tatar
Telugu
Thai
Tigrinya
Tonga
Tshiluba
Tumbuka
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
In this tutorial, we will create this object, this object.
Let's start with this object.
At first start the sheet metal environment.
For that, click on start, mechanical design and generative sheet metal design.
In this part, the sheet thickness is 2 mm.
Click on sheet metal parameters.
Give the thickness of 2 and we will keep the bend radius as 4 and click on ok.
In this object, at first we will create this base plate of 230 by 130.
Click on wall, then click on sketch.
Then select this horizontal plane, then create one rectangle from center.
Click on center rectangle.
Give the center point, take your cursor away and click.
Then give the dimensions.
Click on constraint or double flip.
Then select the line, give the position, double flip the dimension, give the length of 230.
Then select this line, give the position, double flip, give the length of 130.
Then click on exit workbench and ok.
Then to create this flanges of 30 length, click on wall on edge.
Then give the length of 30.
Now this 30 length is from the bottom to top.
Therefore we will select this option.
The first option, where dimensions are considered from bottom to top.
Then select the bottom edges, then reverse the direction, click on reverse position, then select all the bottom edges from all sides.
Now zoom on this corner.
But we have created the wall with outside dimension.
Therefore it is important that we keep this thickness inside.
To keep this thickness inside, click on inward material side.
So that your material will be kept inside your overall size.
Then only it will come correct.
Then click on ok.
Then zoom fit.
Then we will see the top view.
Whether it matches with our drawings or not.
Click on top view.
And zoom fit.
Now if we compare both the drawings.
Now here, holes are not shown.
Now in this case, there are holes.
But in this drawing, no holes are there.
To remove these holes, we will have to change it.
Extremities.
For that, double click on this sheet metal parameters.
And click on this bend extremities.
Then from here, we will select this tangent option.
Or you can also select this linear.
And ok.
Now if we see here, there are no holes.
Some gap is still there.
We will change it.
This double click.
Bend extremities.
And from here, select this closed one.
So that there will not be any gap.
Ok.
Now no gap is there.
And we will check all the other parameters.
Whether the part is made as per dimensions.
For that, click here on major between.
Then select this surface.
Orbit it.
And select this surface.
Here, you can also zoom fit all in.
The length is 230.
And here length is 230.
Then width.
Again select this surface.
Orbit.
Select this surface.
Here length is 130.
It is also correct.
And thickness 2, we already have given the thickness of 2.
Then 30.
So that we will select this top surface.
And this bottom surface.
And zoom fit.
And here actually it is giving an inclined length of 30.2.
But we can see the here.
Z. Z is vertical.
Z is minus 30.
That means thickness of 30 is correct.
If in your case this xyz is not shown.
Then you will have to click on this customize.
And you will have to take here for components 3D.
Here you will have to take.
Then only it will show this component in xyz direction.
Okay.
Cancer.
Now this model is correct.
Zoom fit.
Then to start new model, click on new.
Then select part.
Okay.
Okay.
Then next will be this one.
Now here at first we will create base wall of 180 by 100 sides.
Before that we will set this parameter.
Fit Metal thickness is 1.2.
And inner bend radius is 1.
For that click on sheet metal parameters.
Then give thickness of 1.2.
And radius of 1.
Click on okay.
Then click on wall.
Then click on sketch.
Then select this horizontal plane.
Then create one rectangle from center.
Center rectangle.
Give the center point.
Take your cursor of a and click.
And give the parameters.
Length is 180 and width is 100.
Double click on constraint.
Select this line.
Take your cursor below.
Click double click.
Give the length of 180.
Enter.
Select this line.
Click double click.
Enter.
Then click on exit workbench.
And okay.
Then next will be to create this side walls.
The length of this side wall is 50 from bottom to top.
And these walls are on 180 length.
Click on wall on edge.
Then give length of 50.
Then option is correct from bottom to top.
Then select this bottom edge.
Zoom.
And select.
Then reverse position.
Zoom minus orbit.
Select this bottom edge.
Now again in this case we will need material inside.
If you see the side.
Your material is outside.
Click on this inward material side.
And click on okay.
Zoom fit.
Isometric.
Then next is to create this walls of 15 length.
And there is this gap of 0.5.
Again click on wall on edge.
Then give length of 15.
Then select this bottom edge.
Then reverse position.
And select this bottom edge.
Then this option is correct.
High it is from bottom to top.
Then we need to set this gap for that click on this extremities.
And give your gap value of 0.5.
And click in other box.
Now this gap is applied.
Click on this high tining clay nation.
Again we need to check the material.
We will watch the top few.
Now again this material is outside the length.
Click on this inward material side.
So that it will be within our length.
Then same is required on other side also.
We will select bottom edges on other side also.
Zoom fit.
And select the bottom edges.
And it.
Zoom it.
And select.
Then click on.
Resumetric beam.
Now here it is projecting outside.
It is not required.
If we see here there is a small home.
For that click on the sheet metal parameter one.
Click on bend extremities.
And from here we will select this linear.
There is small hole is there.
Alright.
Now it will match with this one.
And next is to create this cut.
Zoom fit.
To create this cut click on cut out.
Then click on sketch.
And select the surface.
Zoom it.
Now here is a rectangle of 40 by 20.
And location is 30 from both the side.
And then click on rectangle using 2 point method.
Give the first point, second point.
Then double click constraint.
And specify the parameters from this line to bottom line is 30.
From this line to this line is also 30.
Then height is 40.
And width is 20.
Then there is chamfer in the corner of 5 you height and 2 point 5 you width.
For that click on chamfer.
Then we will select this option construction line stream.
And select this line and this line.
Then we will choose this first and second length.
Then press tab to specify dimensions.
Then give first length will be 5 you.
Tab second length will be 2 point 5 you.
Enter.
Same way on all the other corners chamfer.
This is first line, this is second line.
Then tab 2 times and give length of first line will be 2 point 5 you.
Tab and second length for you.
Enter.
Then second line.
Then chamfer.
Then tab.
First line length will be 5 you.
Tab 2 point 5.
Enter.
Then again chamfer.
Select this line as a first line.
This line as a second line.
Then tab 2 point 5 you.
Tab 5 you.
Enter.
All the chamfer are created.
Then click on exit workbench.
Then depth of 1 point 2 is correct.
And limit up to next is correct.
Click on ok.
The cut is created.
Next will be these holes.
At first we will create this hole and then we will array it.
This hole is at a gap of 50 and 9.
And diameter of the hole is 4.
For that click on hole, orbit it and select this surface.
Then click on position sketch.
Double click on constraint.
Select this star and this bottom edge.
Give the length of 9.
Enter.
Then select this star.
Select this vertical line.
Give the length of 50.
Enter.
Then click on exit workbench.
Then give diameter of 4.
Then click on blind up to next.
Ok.
This hole is created.
For that at first we will select the hole.
Then click on rectangular pattern.
The number of instances will be 3.
That is this one.
Second and third.
And the spacing between this hole and this hole will be.
Actually this is 50 minus this 9.
That is 41.
Give 41.
Then for direction click here.
And give this line as a direction.
Now I want this hole at the center.
For that click here on mover.
And give row in direction 1.
Will be second.
Click below.
Now it is at correct position.
Then in second direction click on second direction.
The number of instances will be 2.
And the spacing will be 50.
Minus this 10 and 9.
That is 50 minus 19.
That is 31.
Give here gap of 31.
Click in other box.
Then for reference direction click here.
And select this vertical line.
Then we want it in reverse direction.
Click on reverse.
Then click on the holes.
We should not want those will be removed.
And click on okay.
So these holes are created.
Then we want the same hole on this side.
We will cut them by using these holes.
For that click on cut out.
Then click on sketch.
Then select the surface.
Zoom fit.
Then project these holes.
To project select this circle.
And click on project 3D elements.
Click outside again select this circle.
Again click on project 3D element.
Click outside again select this circle.
Click click outside.
Then click on exit workbench.
And click on okay.
This hole is also created.
Click on isometric view.
Then fit all in.
This object is also created.
In the next lecture we will learn some more sheet metal commands.
Thanks for watching.
We will see you in the next lecture.
Thank you for watching.
And some more sheet metal commands.
Thanks for watching.
Thanks for watching.
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.