Afrikaans
Akan
Albanian
Amharic
Arabic
Armenian
Azerbaijani
Basque
Belarusian
Bemba
Bengali
Bihari
Bosnian
Breton
Bulgarian
Cambodian
Catalan
Cebuano
Cherokee
Chichewa
Chinese (Simplified)
Chinese (Traditional)
Corsican
Croatian
Danish
Dutch
English
Esperanto
Estonian
Ewe
Faroese
Filipino
Finnish
French
Frisian
Ga
Galician
Georgian
German
Greek
Guarani
Gujarati
Haitian Creole
Hausa
Hawaiian
Hebrew
Hindi
Hmong
Hungarian
Icelandic
Igbo
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kazakh
Kinyarwanda
Kirundi
Kongo
Korean
Krio (Sierra Leone)
Kurdish
Kurdish (Soranรฎ)
Kyrgyz
Laothian
Latin
Latvian
Lingala
Lithuanian
Lozi
Luganda
Luo
Luxembourgish
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Mauritian Creole
Moldavian
Mongolian
Myanmar (Burmese)
Montenegrin
Nepali
Nigerian Pidgin
Northern Sotho
Norwegian
Norwegian (Nynorsk)
Occitan
Oriya
Oromo
Pashto
Persian
Polish
Portuguese (Brazil)
Portuguese (Portugal)
Punjabi
Quechua
Romanian
Romansh
Runyakitara
Russian
Samoan
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Seychellois Creole
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
Spanish
Spanish (Latin American)
Sundanese
Swahili
Swedish
Tajik
Tamil
Tatar
Telugu
Thai
Tigrinya
Tonga
Tshiluba
Tumbuka
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
This is tutorial number 50 and it covers how to use the Stiffender feature within KTF-V5.
To start off, open up tutorial part number 50 which is located on the DVD.
Now the Stiffender feature is found in the toolbox over here, or if you go to insert sketch-based features, Stiffender.
Now to use the Stiffender all you need is one profile or one line that's opened and from that you're able to make a Stiffender.
So what we're going to be doing is creating a line along here and extruding it across.
So to start off, let's click this face here and we'll click sketch.
Now when you're making it, when you're drawing these lines in here, there's two different ways to do it.
You can go from line to line, touching the points there, or you can do it inside the box without touching any lines.
So this is two different ways of making a Stiffender.
The first one we're going to make is just draw lines that are inside this box, not touching the edges.
So let's just rotate it around a bit and just draw a little line just like that in there.
And if you look on the side, you can see that it's inside the box.
Now go back up, click Stiffender, and we're going to be using the from side mode.
You're going to be able to use the from top mode when you click on the points to points.
So if we zoom in, what this is going to let us do is we're able to, with the thickens, slowly bring that sketch out.
Now you'll notice that our sketch is only in here, but what this is going to do with the Stiffender is it automatically extends it out to the edges and kind of cleans everything out for you.
So let's bring this out 20 and we'll click OK.
And the Stiffenders come out 20 millimeters.
Now let's double click on this sketch and let's just move this around.
So let's drag this guy more over to here and let's see what our result is.
And you can see that now our Stiffender has moved over also.
Now let's delete this Stiffender and we're going to do it the other way that I was talking about.
So let's click this face, click Sketch.
Now click this face and we'll project the edges, turn them into construction lines, and now we'll sketch from point to point.
So we'll do one from this point along here to a point along there.
Now let's put a little angle in there so we can play with it after.
So we have an angle about 30 degrees. So let's put in 30.
And let's go back up and let's click the Stiffender.
And from this one you can use the from side or you can use from top.
So right now on the from side we're making exactly the same one that we had before.
From top we're going to make one that's going to have a hollow opening in it.
So let's click OK.
And let's click on this surface here and we'll sketch out quickly a rectangle and just cut this a little bit out just so you can see the gap in there.
So if you can see in the back there you have a gap and that's what using the from top compared to the side is there.
And let's go back.
Now let's make the stiffener again using this point to point and we're going to use the from side.
So this is just like the other one. We're just going to extend it out 25.
Click OK.
And we'll edit this sketch. Change the angle to about 60.
And because it was outside it's not going to work.
So let's go back into it.
Put it to 45.
And just bring it in.
And it should work this time.
And it does. So you're able to play around with a stiffener like that.
Now let's do one that's on the top. So let's click this top surface here.
Click sketch.
Now we'll click this face here.
Project it out.
And turn it into construction lines.
And let's just draw a little jagged line across.
And we'll go back up.
And we're going to create a stiffener from here.
Now click OK. And click from top.
So now we're able to create the stiffener from the top in this mode.
So let's bring this down to about 5 millimeters for the thickness.
Click OK.
And now we made a stiffener in here for about 5 mils.
So what the stiffener does is we're allowed to just use one sketch, one sketch line.
And you're able to create kind of like a stiffener inside the part that adds like ribs and whatnot.
Now we're going to make one more from here.
So let's just double click on the sketch.
And let's delete these lines.
And let's just try to make an organic one.
So we'll use the spline.
And just make one with a few curves.
And we'll go back up.
And we've created a stiffener with those curves.
So like I was saying, with those lines,
all you need is one line that's open, not a closed profile.
And then you have to toggle between the from side and from top to get the results that you want.
So by doing this, you're able to create stiffeners inside parts quickly and easily just from a single line.
And that concludes our tutorial on how to use the stiffener feature within KTAV5.
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.