Afrikaans
Akan
Albanian
Amharic
Arabic
Armenian
Azerbaijani
Basque
Belarusian
Bemba
Bengali
Bihari
Bosnian
Breton
Bulgarian
Cambodian
Catalan
Cebuano
Cherokee
Chichewa
Chinese (Simplified)
Chinese (Traditional)
Corsican
Croatian
Danish
Dutch
English
Esperanto
Estonian
Ewe
Faroese
Filipino
Finnish
French
Frisian
Ga
Galician
Georgian
German
Greek
Guarani
Gujarati
Haitian Creole
Hausa
Hawaiian
Hebrew
Hindi
Hmong
Hungarian
Icelandic
Igbo
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kazakh
Kinyarwanda
Kirundi
Kongo
Korean
Krio (Sierra Leone)
Kurdish
Kurdish (Soranรฎ)
Kyrgyz
Laothian
Latin
Latvian
Lingala
Lithuanian
Lozi
Luganda
Luo
Luxembourgish
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Mauritian Creole
Moldavian
Mongolian
Myanmar (Burmese)
Montenegrin
Nepali
Nigerian Pidgin
Northern Sotho
Norwegian
Norwegian (Nynorsk)
Occitan
Oriya
Oromo
Pashto
Persian
Polish
Portuguese (Brazil)
Portuguese (Portugal)
Punjabi
Quechua
Romanian
Romansh
Runyakitara
Russian
Samoan
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Seychellois Creole
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
Spanish
Spanish (Latin American)
Sundanese
Swahili
Swedish
Tajik
Tamil
Tatar
Telugu
Thai
Tigrinya
Tonga
Tshiluba
Tumbuka
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
This is tutorial number 45 and it covers how to use the shaft feature within Katia V5.
Start off, open up a new Katia part file.
Now we're going to be using the shaft feature and to use the shaft feature what we have to do is we have to have two sketches.
So one sketch is going to be a profile and the other sketch is going to be an axis that we're going to revolve this shaft around.
So the shaft feature can be found on the toolbar over here or if you go to Insert SketchBase features you can find the shaft feature here.
So what we're going to do is we're going to set up the two different sketches that we need to create our shaft.
So first off let's click the YZ plane here and let's click Sketch.
And let's click a circle and let's make a circle and we'll dimension this to 100.
And let's dimension the distance from the center point to the origin.
And let's make this 300. And let's go out and let's exit this sketch.
So what we've done is we've created our first profile that we need to create our shaft.
Now what we have to do is create a sketch that's going to be our axis that we're going to revolve it around.
So let's click the YZ plane again and let's click Sketch. And let's just draw a line up and down the origin here.
And let's exit it and that sketch is going to be our axis that we're going to revolve it around.
Now let's open up the part body and you can see that we have one sketch there and another sketch there.
So now let's use the shaft feature. So let's click Shaft. And what we have to do is we have to choose a profile and we have to choose an axis.
So for the profile let's choose the circle and for the axis let's choose the line right there.
Now automatically it's kind of come up with the preview of what we're going to get.
So let's click Preview and we can see exactly what we're going to get.
So we're going to get the circle revolving all the way around to make a ring.
Now let's click OK. And we've created a shaft feature and we've created a ring using the circle and the axis.
So let's get in and let's play around with these parameters a little bit. So let's double click on the shaft.
And what you have is a first angle and second angle. So for the first angle let's reduce this. So let's make this 270.
Click Preview and you'll see that we're chopping out 270. So right now this bit is going to be chopped out.
And let's put this second angle to 90. And let's preview it and you can see that it closes it up.
So we're going to have two different angles going in from this one profile here.
So if we put both of these at 90 and click Preview we're going to have half. So it's going to go 90 degrees this way and 90 degrees that way.
Now let's put this to 130 and let's put this one to 130. And let's click OK.
And you can see that we're revolving 130 this way and 130 that way to create our shaft.
Now let's go into the shaft one more time. So let's double click it and let's click Thick Profile.
And again let's put this thickness to 10. Click Preview and you can see that we're creating a hole or a thickness to our shaft that we made.
Now this is going to work just like the pad that we used before for the thickness and the pocket.
Now let's click OK. And you can see that we now have a hollow opening in our shaft that we just created.
Now let's change some of these sketches that we were using. So let's double click on Sketch 1.
And let's change this from a circle to a square.
So just kind of draw a square around the circle that we have and delete the circle. And let's exit it and let it rebuild.
And you can see that it rebuild with the square rather than the circle.
Now if we go back into the sketch again, let's move this square farther out.
Delete this dimension here. Click Rebuild. And now our entire shaft is now larger and it's been extracted out more.
So to use the shaft feature, you need to have the two sketches. You need to have one that's going to be your profile and one that's going to be the axis that you're going to revolve it around.
Now we're going to do one more and what we're going to do is we're going to put this kind of on an angle compared to what it is right now.
So let's click the YZ plane, click Sketch, and let's draw a line that's on an angle to the origin and click it onto the origin.
And let's make this 45 degrees. Now let's accept this. And let's do another shaft. So let's click Shaft.
Let's click Sketch 1 as our profile and Sketch 3 as the axis. And you can see that it's all on that 45 degree. Let's click OK.
And now we've created the profile and everything on that 45 degree angle.
So like I was saying, you need your two sketches, the profile and the axis. And by playing around with the angles and the shapes of your profile and axis, you're going to get different results every time.
So this is a tool that the more practice you have and the more that you play around with it, you're going to see the different results that you get.
And you're going to be able to utilize and put these different results into use, into your parts and projects that you'll be working on.
And this concludes our tutorial on the Shaft feature within KT of V5.
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.