Afrikaans
Akan
Albanian
Amharic
Arabic
Armenian
Azerbaijani
Basque
Belarusian
Bemba
Bengali
Bihari
Bosnian
Breton
Bulgarian
Cambodian
Catalan
Cebuano
Cherokee
Chichewa
Chinese (Simplified)
Chinese (Traditional)
Corsican
Croatian
Danish
Dutch
English
Esperanto
Estonian
Ewe
Faroese
Filipino
Finnish
French
Frisian
Ga
Galician
Georgian
German
Greek
Guarani
Gujarati
Haitian Creole
Hausa
Hawaiian
Hebrew
Hindi
Hmong
Hungarian
Icelandic
Igbo
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kazakh
Kinyarwanda
Kirundi
Kongo
Korean
Krio (Sierra Leone)
Kurdish
Kurdish (Soranรฎ)
Kyrgyz
Laothian
Latin
Latvian
Lingala
Lithuanian
Lozi
Luganda
Luo
Luxembourgish
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Mauritian Creole
Moldavian
Mongolian
Myanmar (Burmese)
Montenegrin
Nepali
Nigerian Pidgin
Northern Sotho
Norwegian
Norwegian (Nynorsk)
Occitan
Oriya
Oromo
Pashto
Persian
Polish
Portuguese (Brazil)
Portuguese (Portugal)
Punjabi
Quechua
Romanian
Romansh
Runyakitara
Russian
Samoan
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Seychellois Creole
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
Spanish
Spanish (Latin American)
Sundanese
Swahili
Swedish
Tajik
Tamil
Tatar
Telugu
Thai
Tigrinya
Tonga
Tshiluba
Tumbuka
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
This is tutorial number 22 and it covers how to rotate your sketch within KT-AV5.
To start off open up a new KT-A part file and once you've done that let's go into the sketch workbench.
So click sketch and click any of the planes.
Now what we're going to do is I'm going to show you how to rotate your sketch within KT-AV5
and again the reasoning behind this would be if you have a very complicated sketch
and you need to rotate it a little bit rather than redoing your entire sketch.
You're able to just rotate it and shift it.
So what I'm going to do is I'm going to draw out a profile.
So I'm just going to draw it out from the center point
and just end it there.
And to rotate you'll find it in this toolbar along with the translate and the scale.
And you can also find it if you go to insert, operation, transformation and you'll find rotate.
So with rotate you're able to either select a single line or you're able to select the entire sketch.
What I'm going to do first is just do a single line.
So let's click this line here and let's click rotate.
Now with rotate again you can make duplicate instances.
So you can turn it on or off.
In this case we're going to make duplicate instances. So right now let's just do one.
And what you have to do is you need to select the origin where you're going to rotate around.
So in this case we're going to use the origin of the sketch.
So we'll click this point here.
And now what you have to do is you have to kind of just draw a line.
And that's what it's kind of prompting you to do.
And from this line we're going to rotate around.
So the longer you make this line the easier it is for you to manually move it around.
The harder it is the harder it is to move it around as it's going to be a lot quicker to change the value.
So we'll make it just about the same length as the line we're going to rotate.
And as you see as we rotate the part is also rotating.
So you're able to either rotate and snap to a point or you can type in a value.
So this first one let's snap it to a point.
We'll snap it to this point here.
And now we've duplicated that sketch there.
Now press Ctrl Z.
Get rid of it and we'll do another one.
Click rotate.
Click that center point.
Go straight up.
And this time let's key in 17 degrees.
Click enter.
And now it's moved 17 degrees.
Now press Ctrl Z.
And just if you didn't notice before when we're doing this,
it goes in five degree increments.
So every time you move it's going to go up five degrees or go down five degrees.
Now this time what we're going to do is we're going to make ten instances.
And what we're going to do is we're going to make the angle in between each one.
We're going to make it five degrees.
Click OK.
And now we have that line at five degree increments all the way around.
Now press Ctrl Z and we'll get rid of those guys.
Now what we're going to do is we're going to rotate this entire sketch.
So let's highlight the entire sketch.
Click rotate.
And we're going to put it down to one instance.
We're going to duplicate it.
And we're going to do it around the center point.
So we're going to straight up.
And we're able to rotate this around as such.
Now let's put this to 90 degrees.
Click OK.
And now we've rotated that entire sketch 90 degrees.
Now let's draw another sketch down here.
And what we're going to do here is rotate and just rotate the sketch alone.
So let's highlight the entire sketch.
Click rotate.
And we're going to uncheck the duplicate.
Now we're going to rotate it around this point here.
And we're going to key in 90 degrees.
Click OK.
And now our whole sketch is translated 90 degrees.
Now again, like I said, this is a great tool when you already have a sketch you like.
But you need to just shift it or rotate it a little bit rather than going back and doing the whole sketch over with say a five degree shift.
All you have to do is rotate using the five degree shift and your whole sketch will rotate.
And that concludes our tutorial on how to use the rotate sketch feature within KT of E5.
Can't find what you're looking for?
Get subtitles in any language from opensubtitles.com, and translate them here.