Original subtitles

Hello people.

And we'll go into this new exercise in where we are

going to practice more our drew in skills.

This time we will draw a house plant floor.

So I want you to go over File Import.

We know this already and this time,

let's open this house plant floor File Import.

First click on the origin and now be

careful because our image has unskilled.

Second click wherever you want.

And once our image is on

the ground floor, fire scroll in,

we will see that we have this graphic scale, 01.5 m here.

We have as well here, the North.

But what is really,

really important now is this graphic scale,

because I want you to do this exercise

practicing with the real measurements of this house.

So first of all, camera parallel projection.

We know this already top view.

We are ready for working nicely.

Then I go to this graphic scale and

then we will use this tool, tape measure tool.

Remember that this tool has four properties.

First of all, we can measure things.

Of course, we can create guide lines or points,

and we can scale the entire model as well.

This is what we're gonna do right now.

So one-click here, first single click on zero.

Let's see the length of this distance,

3.49 and it has to be 5 m, right?

So it is not correct obviously.

So second click here.

Then I write down the correct measure,

five Enter, it will pop up

this window that you want to resize the model.

Note that components within the model that we're

loaded from external files will not be resized.

This is a very, very important message,

will go deeper into these methods in the next future.

Because according to this message,

I want you to understand perfectly

what you can do and what you cannot do.

So we will resize all the model.

Yes.

And now all the entire model has been resized,

which means that our image has

been resized, not this woman.

Similarly is her name.

Check that the high is the same because the matter is

considered an external component

for schizo, again, top view.

So let's start drawing the external walls.

We'll do it using guidelines.

So letter T, one click on the edge of the image

and then I can drag a guide line parallel to that.

Ed's. Remember that by clicking control,

you will allow this tool,

this tape measure tool,

to create guidelines now or to

use it just for measure things.

So tap control, you will have

that tiny icon representing

the guideline and then keep drawing,

scrolling for being precise.

And second click here.

Now I will use this guideline

in order to create another one.

The thickness of this wall,

let's say it will be 0.25

m. We will keep this thickness in all the external walls.

Remember that the images are always references.

Scroll out.

Let's go with this wall letter T,

click and release swimming.

Second click here.

I will use this guideline.

So one click and release and 0.25 second click,

scroll out scrolling, we can

pan will repeat exactly the same process.

The scroll out.

We open the screen for going to this side,

to the right side, we compound letter T and again, 0.25.

Here we are scrolled out.

And now let's use the line tool or even the rectangle.

This is up to you.

If I use a rectangle,

is gonna be faster.

First click, second click on the second rectangle.

First click, click.

And now I will select this surface and I

will delete it in order to

see the image through this wall,

I will use the X-ray style.

So now I can continue drawing.

This time the holes for the windows.

Let's check this measurement, 1.20 L.

We close the hole,

we can erase this guideline.

We remember that the whole for this window is 1.2.

Here we need to do a whole for adore, so l.

And again, I will use

the guideline zero-point that say 0.8.

This is the normal distance for

other erase, again the guideline.

And now we have just to continue

drawing all the windows and doors.

Well, once you have finished your external walls.

We can remove all the guidelines to clean our drawing.

And let's go now with internal partitions.

Again, we will use

the guidelines to make sure that we are drawing

precisely letter T first guideline, e.g. here.

Then let's set the thickness

of these internal partitions.

Zero-point ten could be nice.

It will be always the same.

Now, again, it's just a matter

of repetition here for this partition,

I will set zero point to time now for

using the line or

the rectangle first rectangle tool here.

And then one surface has been generated,

but we will not pay attention to it is not important.

At the end, we will correct all these things.

So let's continue drawing our rectangles.

Here.

I recommend you to use the pan by holding

Shift and the width of the mouth because it is very,

very handy when we are

drawing and we don't lose the tool that we're using.

In this case the rectangle.

I can start my rectangle, e.g.

here using the pen tool in the middle, release.

And then I still have the rectangle on.

And I can finish it.

Once we have finished the internal partitions,

time to erase the guidelines.

I will use the eraser this time

clicking and holding my left button.

And now I need just to draw the holes for

these kinds of doors sold letter L.

And again, if I want to be precise,

I need to use the guidelines 0.78, let's say 0.7.

We close the line.

We can erase this guideline at

this very moment and we repeat this same operation.

Of course, there are more ways for drawing this

because it is kind of slowly to do it this way.

But we haven't learned already those tools as e.g.

the copy tool, because here I could

select this element and say Copy,

right, the distance 0.7.

And here we are.

I think it's faster, right?

But now we are learning to use

the guidelines that the rectangles and all this stuff.

So we have to be patient and do

it using the tools that we have learned.

We have to do it this way.

I know is a little bit slow, maybe repetitive.

But it's the way once we have our drawing like that.

Now, I would suggest you to use the eraser in order to

just delete all the lines

that we don't want in a very easy way,

clicking and dragging e.g.

here, I committed a mistake,

but it is very easy to now fix those things for me,

using the eraser is very, very relaxing.

So we have almost finished.

I will orbit now.

Camera, perspective, switch off

the x-ray and then we can see perfectly our surfaces.

The space key for the selection tool,

one click here on this surface and

delayed the same here and the same here.

We could delete as well the surfaces

for the entrances eraser again,

click and drag, click and drag, click and drag.

We have now our drawing ready for extrude,

but first looked at our surfaces.

All of them have the buck color towards us.

This is not good because when we extrude those surfaces,

the whole 3D model is going to

have the back color towards the camera.

So I strongly recommend you to reverse faces

when we're still in our two, the model.

Then I will make

a selection box just for selecting the geometry.

Then I will place my mouse above any surface,

right bottom reverse phases.

Here we are.

Now we could use the Post poll tool easily,

but this is something that we will

do in the next episodes

after learning how to use

this tool in a professional way.