Original subtitles

Interface of the land 100 standby 1 IP 10 to 1 that 100 to 5 4 standby.

1 priority 200 standby.

1 pre-emption.

So looking at code to show run shows us that this is the configuration on the veal and 100 and the switch

has become the active rota

on call 1 we're going to do something similar.

Stand by one IP tendered one third one hundred two five for show standby.

Still listening at the moment but after a while that should go to active.

It's now speaking in other words sending out just happy messages and notice it's now gone to standby.

So show standby on vlan 100.

The local writer is in standby mode active rota is called to again the local Rada is standby.

Now the lost V Line to configure and one not to forget is V Line one.

Don't forget to configure v land one because your layer two switches here and to the access layer also

need a default gateway show spanning tree v land one local switch is the route.

So we want to configure it as the HSR P primary so stand by one IP tendered wandered wandered too far

for standby 1 priority 200 standby 1 pre-emption to show run and we'll look at a V Line 1 that's the

configuration

configure code to interface v land 1 standby 1 IP 10 1 1 2 5 4 we can see that call 1 has become the

active router for VLAN 1 so shows standby

for VLAN 1 call 1 is the active router.

Same for V Line 10.

Same for v land 30 it stand by for VLAN one hundred and it standby for VLAN twenty on the side show

standby.

V land 1 it's the standby rather standby for v land 10 it's active for v land twenty stand by for v

land 30 active for v land 100 so that's good.

I think we've configured it USP successfully on our core switches.

Now we need to configure default gateways so we've already configured P.S. 1 to use 10 1 10 to 5 4 as

the default gateway lets configured PCI to config on PCI to

Gateway will be tendered 122 22 5 for DNS server will be Google IP address will be tendered one top

20 top 10

slash 24 mosque so that's the IP address we need to use 10 1 2010

go to desktop command prompt IP config shows us that information cannot ping its default gateway.

Yes it can.

Can the P.C. ping P.S. 1

k so there you go.

Just took a bit of time but notice now.

P.S. to camping P.S. 1.

So back on P.S. 1 kind of paying P.S. 2.

Yes it can.

Notice if we look at the op cache we don't see a mac address for P.C. 2 because to get too P.C. to traffic

is going via the default gateway which is the ages of P rather

and the same is true on P.C. to we need to configure P.S. 3

Gateway is gonna be tendered wondered 32 to 5 for DNS server is Google

IP address will be tendered one thirty dot ten slash 24 mosque as shown here.

Desktop.

Command prompt IP config.

That looks good.

Can we paying P.S. 1 Yes we can.

Can we paying P.C. too.

Yes we can.

So that looks great but notice we won't be able to ping our switches.

Why can't we ping the switch

if we run a debug on that switch

so use the command debug IP ICMP.

We should be able to see if traffic arrives after that switch.

And notice you can see it arriving so the ping gets to the switch but it doesn't get back again.

And that's because we need to configure a default gateway on the switch

and to do that.

We use the command IP default gateway and we specify our default gateway which is the HS IP router.

And now you can see that pings are succeeding so I'll turn off debugging here.

Command is unable to turn off debugging save the config while we there and notice P3 camping switch

one but can't ping switch to the switch here because again we need to configure a default gateway

to show IP interface brief IP address is tendered wandered wanted to show ip route shows us that we

don't have a default gateway so IP default gateway tendered wandered wandered too far for show IP round.

Default gateway is now configured so back on P.C. 3 hopefully we should be able to ping switch to which

we can pings are now succeeding.

We need to do something similar.

On switch 3 Access Switch 3 IP default gateway

10 to one dot 1 2 5 4

show IP round shows us that we do have a default gateway configured I'll save the configuration on PCI

3.

Can we ping access 3

took a while.

But the answer is yes we can now ping access 3 Can we.

Paying the server which has IP address 10 100 100 answer is no because we need to configure the server

so on the server default gateway will be tendered one dot one hundred two five four will set to the

DNS server to Google IP address will be tendered 1 100 100 slash 24 mosque

open up a C D prompt or command prompt IP config shows us the IP address of the server can at paying

P.S. 1

yes it can.

What about P.S. 2.

Yes it can.

What about P.S. 3.

Yes it can.

Can the pieces paying the server.

Yes.

P.S. 3 can ping the server.

What about PCI 2.

Yes it can.

What about P.S. 1 yes it can so we've successfully configured IP connectivity in the campus we've configured

H.S. IP but we still need to do however is configure UI JLP on the core Rada and on the ISI are.