Original subtitles

In our next practice lab we'll take a look to the entire will and routing configuration.

We are once rich and three lands created on that switch and we have tested at zero for 5 and 6 are connected

to P.S. 1 3 ms 1 2 and 3.

And our first returns 0 1 port of the Civic is connected to the rorters geek 0 0 interface.

So first configure so each Port Vila hands and proper port modes so I understand that villains are not

created so needs to be create I think we'll take a look to try to paint Pasi 2 from P.S. 1 then configure

daughter's geek 0 1 sub interfaces with proper I pair this.

I think this is wrong with them.

This is gonna be gig.

0 0 cousin in the figure is 0 0.

And configure rather otherwise stick and in the first step.

Try the pink piece it too from P.S. 1 again and let's go first.

I'm going to make the configuration of the switch.

I will create realism

tend to end in 30 and I'm going to attach fest 0 4 to 10 0 5 to 20 in 0 6 to 30 and these guys will

be switch port mode access

and I'm going to make the

first 01 to transport.

Let's go

woops

let's make it some bigger that's better I think

and let's create my v lines first in a row and config to create the airlines I'm using we land and will

a number that I want to create.

Command will 10 and their OK exit and I want to take a look if there is a will on configured on the

switch first.

As you can see the we just have default villain and we land terror right now.

That means we need to create to an end.

3 2 we land to any and we land 30 pretty straightforward and pretty cool.

There is no problem in here.

Now I need to attach my ports to that Wilkins interface first if there is 0 4

will be a access port because I'm gonna use this port with one bill and only and this port

will access to relent 10

okay in the face first Internet 0 5 will be an access port again

and we are gonna access to the real to any

good

and my sixth port will be an access port again

and I'm going to access to William 30 whoa pretty cool.

Now we need to configure the right port to also.

This is precedents at one

I'm making here wrong using these with port mode to run comment.

All right.

I think we accomplished the first step but I need to double check it configure switch port millions

and port proper port modes.

All right.

I made my 0 1 as a talk and I created these real lines and attached these ports as access ports to this

valence.

OK.

And now paying P.S. 2 from P.S. 1.

I'm gonna go to P.S. 1 amping fitted up 3.

Is there a line for Nat lemme see.

Request timeout request timeout

OK.

As you can see that we cannot ping P.S. 2 from P.S. 1 right now.

Here is the bad nose.

Well I don't think so because we know how to communicate different villains.

We just need a layer 3 device in this scenario.

This is rather a and I hate to create sub interfaces

and use get the addresses of these devices for my each sub interface.

So I'm going to create a sorry.

I'm going to assign

these sub interface the IP address of the gateway of P.C. I'm this sub interface should have an IP address

of 51 and this sub interface should have an IP address of sixty one

and please don't forget that we need to take that sub interfaces because of we are gonna make real and

communication over them

all right.

Let's go into the rather and CLIA.

I'm gonna go to these sub interface mode interface key 0 0 that come first

I'm going to use these as the gateway of the wheel and 10 so my IP address but first I need to take

this with Vaillant 10 please remember it then I'm going to use the IP address of 41

all right.

Go

51 and 61 will be the other sub interfaces

so I will go to the interface.

Geek

zero slice zero up to any and IPA.

This will be 50 but we need to first define the encapsulation as you can see in the morning to Oh no

I clicked the wrong button.

It also whereas it no.

This is gonna be 20 surely.

And my my IP address will be

60

Okay and let's go to the left sub interface

encapsulation that one to 30 and we'll have an IP address of

I think I configured the wrong IP address.

Okay this is gonna be overlap.

What I did is I forget to type 50 for the uh 2 anyway then and I'm gonna roll back down interface kick

no IP address and we'll have an IP address or 50.

This is gonna be 15 here

and afters I will go to the

last interface and I'm going to assign my IP address but first I then remember if I used encapsulation

and I'm assigning my IP address now

okay.

Well your configuration you can make some mistakes and you need to quickly fix these mistakes guys.

Okay.

I completed my configuration right now.

There should be no problem.

So step two is accomplished and I'm not trying to ping P.S. To from P.S. 1 again P.S. 1 I'm not a ping

I'm gonna pinging

this IP address again.

Here is the good news.

Here is what I want to see.

Seriously.

All right.

As you can see that we weren't able to ping before configuring our layer 3 devices.

We couldn't make a communication between different villains.

But after making the related configurations my pain was successful and I was able to make communication

between different devices between different worlds.

All right guys we have accomplished our goals and there is nothing to do more about this scenario right

now.

And thanks for waiting.

See on the next session.