Original subtitles

I'm Jake O'Neal, creator of Animagraffs. And this is how a Formula 1 race car works.

Let's start with Aerodynamics, which is how the car interacts with

and moves through the air around it. It's best to focus on overall theory

here to avoid getting lost in the absolute maze of individual aerodynamic features.

The front wing curves upward, forcing air to move around it in such a way that a high pressure area

forms above the wing, with a lower pressure area beneath. This pressure difference is a contributor

to a kind of suction force called "downforce" that pushes or sticks the car to the track.

Where the wing ends and these different pressure zones meet, the air crashes into itself,

creating a spiraling vortex. Vortices cause drag, which tugs at the car,

slowing it down. A cap on the wing tip interrupts vortex formation for a less intense effect.

The pointed, curved-in surfaces on the inside edge of the wing intentionally shape

and direct a vortex around the floor of the car, sealing in the clean air that passes underneath.

So, while vortices do cause drag,

they're also a useful tool to separate and seal in different areas of airflow.

As a matter of tradition, F1 cars don't have fenders, and the open,

spinning wheel and tire combination is a major source of dirty, turbulent air.

Turbulent air is unpredictable and not very useful for aerodynamic goals,

like generating downforce. Directly behind the tires, barge boards condition or "clean

up" some of this airflow while also pushing lots of dirty wheel air away from the body.

The narrow gap between the car floor and the track

turns the entire floor into a giant downforce generator as air squeezes,

thins, and rushes beneath the car at a different rate and pressure than overhead air.

The floor has a forward tilt or "rake" that creates very low pressure at its narrowest point,

but allows air to more smoothly rejoin ambient air pressure as it flows out the back.

A diffuser at the rear amplifies this goal, with its more pronounced upward curvature.

The diffuser also has vertical vanes to control and direct the

massive vortices that form behind the car as air pours out from underneath.

Clean air is directed into the side pods for cooling purposes;

this stream passes through the car and out the back beneath the rear wing. The smoothly contoured

body guides airstreams gracefully around bodywork for predictable handling under extreme conditions.

The upward-curved rear wing, which is another critical downforce generator, has notched end

caps, with gaps, and louvers to allow some air to combine early, altering and shaping

rear wing vortex characteristics. It's also where, in wet conditions, the noticeable, misty wing tip

vortices sometimes appear in plain sight. A hydraulic actuator tilts a section

of the rear wing when the drag reduction system or DRS is engaged,

generating less rear downforce but allowing higher overall speed.

The massive area of dirty air behind the car can make it difficult for other cars to approach

and overtake. It's worth noting here, that in coming years the aerodynamic

design regulations for F1 cars are set for major changes to encourage closer racing

and overtaking. The airflow pattern might look more like this than the current wide, dirty wake.

Now let's go underneath this exterior bodywork, starting with the core support structure.

A carbon fiber shell called a monocoque, the engine heads and block, and the gearbox enclosure

form the main structural support for all other systems.

There's no additional frame or chassis underneath. Key components are either

mounted directly to the surface or housed inside of these sections.

Suspension Both front and back

suspension setups share similar components: upper and lower wishbone arms with a push or pull rod.

The wishbones are rigid structural supports with limited vertical travel. At the front,

where heat isn't an issue, wishbones are directly attached to the monocoque and

have simple flexure joints, designed to bend under load.

At the rear, where engine heat can be intense, spherical bearings are used.

The push or pull rod is where the action happens. Our model has push rods in the front

and pull rods in the back, which simplified, just indicates how the system is mounted:

to push or pull connected suspension parts. If parts can be mounted down low

for a lower center of gravity, all the better. The pull-rod connects to a rocker and damper,

which we call shock absorbers in normal cars. But instead of large coiled springs,

F1 suspension uses a small metal rod called a torsion bar that twists under load. One side of

the torsion bar moves with the outer cylindrical shaft while the other side is stationary.

Both independent suspension sides are linked to a central roll bar that twists to limit body roll.

Heave is the vertical position of the car, which is critically important for proper aerodynamics.

The heave spring and damper cleverly come into play when both sides move up or down together,

for example, during acceleration or braking, but are mostly inactive for other movements.

The heave spring in our model is a stack of flexible, cone shaped washers that

compress together under load. Washers can be added or subtracted for fine adjustments.

The front suspension handles similar tasks to the rear, but with different techniques.

The steering system is closely packaged with front suspension. A track rod links each tire

to a fairly standard hydraulic rack and pinion setup, with the steering column extending into

the cockpit. The rear suspension has a track rod as well for vertical tire angle adjustment.

All wheels must be attached to the car with wheel tethers. These are strong cables that

keep wheels connected to the car in the event of an accident. They're required to pass through more

than one suspension element for increased safety. With few exceptions, most exposed suspension

elements are either made from or bonded with carbon fiber for better aerodynamics forms.

This is another major reason suspension parts are packaged inside body work,

away from outside air wherever possible. Braking system

A master cylinder and reservoir controls and stores hydraulic fluid for braking. F1 cars have

two master cylinders and accompanying reservoirs, for front and rear brakes respectively. The

cylinders are mounted to the brake pedal on one end, and a threaded brake bias screw on the other.

This bias screw is electronically controlled, and can be adjusted on the fly as directed

by the driver. The screw position allows different pressure to the front or rear brakes.

Brake lines snake through suspension elements to the brake caliper and shoe assembly.

Intense brake heat must be precisely managed, so the entire inner wheel assembly is covered

by a ducted carbon fiber shroud. The front wing helps direct air into brake ducts

and through the inner wheel for cooling. The calipers are mounted at the lowest

possible position for proper brake bleed -- that is, ensuring troublesome air bubbles can

escape hydraulic brake lines -- while maintaining a low center of gravity.

The brake discs and shoes are made from a carbon-based material. The disc has

thousands of small holes extending from the center outwards for maximum cooling effect.

The rear brakes have a similar design strategy but have become smaller in

recent years with the addition of the MGU-K, or Motor Generator Unit - Kinetic.

The MGU-K is geared to the crankshaft and functions as an electrical power generator

to charge an on-board battery, as driven by a portion of rear braking forces.

A computer mounted inside the gearbox enclosure manages and balances this complex system.

The wheels are secured to the hub with a single wheel nut. Metal retention pins keep the nut

securely in place. A specially designed wheel gun pushes these pins down when removing the nut.

Engine and associated systems

F1 cars use 6 cylinders in a V configuration.

The pistons are somewhat flat and small to suit the high-revving engine.

Intricate exhaust headers feed a comparatively massive turbine at the rear of the engine

which is part of a split turbocharger design that separates these normally stacked turbo components.

Red-hot exhaust gasses drive the turbine wheel,

which in turn spins the front-mounted compressor wheel,

drawing in and compressing huge quantities of air.

All this pressure adds unwanted heat to the incoming air,

so one entire side pod is dedicated to the intercooler.

That path of incoming air looks like this: the compressor draws air in

through an intake duct mounted in the roll hoop above and behind the driver's head.

Hot air leaves the compressor towards the intercooler.

Side pod air rushes by the intercooler's tubes and fins, cooling the compressor air inside.

The now cooled air passes through special split ducting that feeds separate intake plenums.

These are chambers designed to keep air pressure balanced between cylinders.

Intake trumpets extend into the plenums for specially tuned air delivery to each cylinder.

The sidepod air flows by and cools the engine and

other internal parts on its way out the back of the car.

The exhaust section of the turbo has dual wastegates corresponding to each exhaust input,

to vent off excess gases when needed. Wastegate pipes follow the main exhaust pipe out the back.

A high-tech heat recovery unit sits between these turbo compartments,

called the MGU-H, or Motor Generator Unit - Heat. Excess heat from turbo

gases drives this unit to act as an electric generator to charge the on-board battery.

Energy Recovery System (ERS)

The MGU-H and the previously shown MGU-K together make up the hybrid functionality of the modern F1

car. Both units generate electrical charge for the battery. Once sufficiently charged, the battery

can send power back through the MGU-K unit, which again, is geared to the crankshaft. In this way,

the MGU-K can generate an additional maximum 160 hp, or as much as a separate small car engine.

Cooling Various additional radiators for cooling

occupy the opposing side pod. This includes the main engine cooling radiator, an oil cooler, and

a battery cooler. An additional bank of radiators sits in the path of a separate roll hoop air duct,

to cool hydraulic oil, gearbox oil, and the MGU-H and K systems.

F1 teams may locate specific radiators in different positions than I've shown here,

though the general available spaces will be similar. They may also use water-driven

intercooling for turbo air, in contrast to the simpler air to air setup I've chosen.

Fuel tank The fuel tank,

also called a fuel cell, is a nearly puncture-proof kevlar bladder lined with rubber.

It occupies an isolated compartment in the carbon fiber monocoque shell, and fills all available

space. F1 fuel cells can hold an incredible 30-40 gallons (115 - 150 liters) of fuel,

which is just enough for a single race as pit-stop refueling is not allowed.

These cars get an estimated 4-6 miles per gallon of fuel (1.7 - 2.55 km/L)

The tank has various internal baffles with one-way valves to tame the sloshing liquid

under incredible racing forces. The goal is to keep the large fuel mass centered and low,

and also to prevent foaming and fuel pump starvation.

The engine oil tank is placed between the engine and fuel cell.

Gearbox The 8-speed gearbox (7 forward plus reverse) sits

behind the engine in its own aluminum cartridge. The rear differential gears connect to rear axles

with special tripod joints that allow spinning axles to tilt with the rear suspension movement

Safety systems F1 cars have robust safety

systems. The rear crash structure protects against rear impact. Side crash structures

are concealed within the aerodynamic bodywork. The removable front nose section handles front impact,

and the all-important monocoque forms a protective cocoon around the driver.

Also attached to the monocoque: a halo device which was implemented in 2018

for additional driver safety, and a roll hoop. The driver's helmet is kept within a specific

angle from the roll hoop to the body for maximum protection in the event of a rollover.

Cockpit F1 racing seats are crafted from molds

taken from a specific driver's body. The driver sits in a reclined position, almost like laying

semi-upright in a hammock. A six-point harness keeps the driver in place. The seat

wraps around the driver's body wherever possible, and safety structures surround the helmet area.

Drivers wear a special brace called the HANS or head and neck device to limit head movement

in adverse conditions. A connected strap clips to either side of the helmet,

and the shoulder harness straps keep the device pressed against the driver.

A drinks tube extends over the shoulder;

it's connected to a small fluid reservoir to keep drivers hydrated while racing.

Drivers use different helmet front and rear spoiler designs to keep their helmets from

lifting or moving around with sometimes dramatically shifting air pressures.

In recent years, the visor opening has further narrowed to protect the more fragile

visor area from puncture or breakage. Cockpit design makes efficient use of

all available space, such that drivers must remove the steering wheel to exit.

Steering wheel This is the famed Formula

1 steering wheel. Driver's mostly don't need to remove their hands from the wheel for steering,

so the wheel doesn't need to be round.

A customizable display at the center shows the current gear as the largest item,

along with things like lap times, tire and brake temperatures, average speed, and so on.

The daunting array of knobs, dials, and LEDs

gives drivers and teams fine controls that can be adjusted on the fly during a race.

Clockwise from the upper left, there's the energy recovery system dial to control the MGU

H and K. Left and right menu navigation buttons. A push to talk radio switch for team communication.

LED warning lights for critical systems, a row of LEDs across the top of the display

acts as a rev counter and shift light system, the launch control switch, which is turned on

for race starts and off when racing, the brake balance dial for front and rear brake bias,

a pit limits button to automatically impose things like pit lane speed and acceleration restrictions,

an engine mapping dial to alter engine performance characteristics, DRS toggle button,

rear differential lock open or closed adjustment, with separate turn entry and turn exit adjusters.

The drinks dispenser button. More settings navigation buttons.

Three programmable preset dials for the engine, chassis (suspension),

and a scenario selector for things like wet weather or tire preservation presets.

The neutral button is for neutral and reverse gears, which can't be selected with rear paddle

shifters. A "message ok" button, an overtake button to instantly apply optimal settings

for overtaking, and finally, a hydraulic settings dial to control the complex hydraulic components

spread throughout the car, for example in the gearbox and suspension systems.

Paddles at the back of the steering wheel handle gear shifting up or down.

The middle paddles are driver customizable. And both bottom paddles actuate the clutch. Only one

clutch paddle can be used for race start. Once in motion, the clutch isn't needed for gear shifting.

Further down into the cockpit we see the gas pedal with contours to wrap around the

driver's foot so as to keep pedals completely separate, and the brake pedal on the left.

Sensors There are sensors

all over these cars. For example, a pilot tube at the front measures air speed.

The driver's custom moulded earplugs have an accelerometer to track head movement.

There's a microphone at the rear to pick up exhaust sound.

For size comparison, here's our average height driver model standing beside an average sized car,

next to our Formula

car. Even with the level of detail I've strived

to attain here, there's so much more. Formula 1 cars really are incredible racing machines.